Raven RS Lite Calibration And Operation Manual Download Page 61

Page: 61 / 125

016-4010-001 Rev. J

DIAGNOSTICS AND TROUBLESHOOTING

RESUME SWITCH

The status of the enable switch (e.g. foot switch) used to engage the steering system.

DISENGAGE SENSOR

Status of the pressure sensor used to disable steering when the steering wheel is turned.

WHEEL ANGLE SENSOR

Displays the status of the position sensor.

Display

Message

The resume switch is set in the OFF position.

The resume switch is in the ON position.

Display

Message

The SC1/TC1 disengage sensor is active. The SC1/TC1 system cannot be

enabled.

The SC1/TC1 disengage sensor is out of range or disconnected.

The SC1/TC1 disengage sensor is inactive. The SC1/TC1 system can be

enabled.

Display

Message

The wheel angle sensor (WAS) is out of range or disconnected.

Wheel angle sensor (WAS) is not calibrated.

The wheel angle sensor (WAS) is calibrated and ready to operate.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands