manualshive.com logo in svg

Raven RS Lite, Calibration And Operation Manual

Share
Download
Raven RS Lite Calibration And Operation Manual Download Page 97

016-4010-001 Rev. J

91

SLINGSHOT

• Touch the refresh button in the lower, left corner to update the list of available WiFi networks.
• Select an available network to enter the WiFi password and connect to the selected network. The network to 

which the system is currently connected will display with a green check mark on the WiFi Connection Status 

page.

MANUAL HOTSPOT

Select Manual Hotspot to broadcast a hotspot for local WiFi devices.

RAVEN AUTO

Select Raven Auto to allow the system to automatically select the best WiFi network connection. To change which 

WiFi network the system is connected to, select the Manual Client mode.

NOTE:

When set to Raven Auto, a small “A” indicator will be displayed to indicate Raven is controlling the 

Hotspot and WiFi settings for the system.

FIGURE 14. WiFi Connection Status

RTK SOURCE SETTINGS

FIGURE 15. RTK Source Page

Summary of Contents for RS Lite






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands