Raven RS Lite Calibration And Operation Manual Download Page 89

Page: 89 / 125

016-4010-001 Rev. J

SLINGSHOT

CELLULAR STATUS

The table below defines some of the terms used as cellular status:

The RS1 unit is equipped with a cellular modem, but the feature has not been

unlocked. Contact your local Raven dealer to purchase feature unlock codes.

The RS1 unit is not equipped with a cellular modem.

Status

Definition

Cellular APN

Displays the current APN used by the cell mode. If Not Available is displayed,

either no cellular connection was established or the user didn’t enter an APN.

WAN

Displays the Wide Area Network (WAN) IP address the cell modem is receiving

from the network.

Cell Signal

Displays the current RSSI (signal strength) of the cell modem.

Cell Service

Displays the current cell service connection type.

Roaming

Status

Displays if the cell modem is roaming.

Display

Message

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands