Raven RS Lite Calibration And Operation Manual Download Page 72

Page: 72 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

522825

.19

TCU disconnected.

1. Check cabling and connections.
2. Check machine TECU version and OMNiDRIVE

unlock.

3. Create a new RS1 profile.

522826

.16

Invalid pitch.

A pitch greater than 15° has been detected for an

extended period of time. Confirm that the RS1 is

mounted securely to a flat surface. Confirm that any

sunroofs are closed.
If the issue persists, re-calibrate the terrain

compensation. Review the

Terrain Compensation Setup

section on page 45 for additional assistance.

523766

.31

Steering control partner

serial number mismatch.

Select the correct steering profile or connect to the

correct machine and steering control unit.

523827

Reverse steer not

supported.

Reverse steering is not supported on this machine. If the

machine is moving forward when this DTC activates,

select the direction toggle icon on the field computer or

the RS1 UT.

523830

.31

Steering not unlocked.

Enter a steering unlock code. An unlock code is not

necessary if using a SmarTrax MD unit.

523832

GPS mode not unlocked.

Contact a local Raven dealer for a GNSS unlock or select

a different GNSS correction type.

523839

.31

Selected tuneset not

released.

1. Update the RS1 software for the latest list of released

tunesets.

2. Recalibrate RS1 using a generic tuneset.

523842

.31

Liability acceptance.

Accept the RS1 liability.

523843

Lost internal

communication.

1. Cycle power to the RS1.
2. Ensure proper CAN termination.
3. Check cabling and connections.

Code ID

Description

Recommended Actions

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands