Raven RS Lite Calibration And Operation Manual Download Page 52

Page: 52 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

SERIAL OUTPUT CONFIGURATION

FIGURE 6. Serial Output Configuration Page

Config Types.

Allows the RS1 system to toggle between a serial 3D compensated GNSS position output or a

simulated radar output.

NOTE:

The baud rate and message types are not used in radar outputs.

GPS OUT

Baud Rate.

The rate for messages transmitted over the serial port. This rate must be set to match the devices on

the system which are intended to receive messages from the RS1 or RS Lite.

NOTE:

The default baud rate setting is 115200 and is recommended for all steering systems.

Message Types.

Set the frequency for each required NMEA message.

NOTE:

Changing message types and rates may cause poor system performance. It is not recommended to

change message rates unless instructed by documentation or Raven technical service.

DIFFERENTIAL CONFIGURATION SETUP

FIGURE 7. Differential Configuration Page

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands