manualshive.com logo in svg

Raven RS Lite, Calibration And Operation Manual, Page: 125 / 125

Share
Download
Raven RS Lite Calibration And Operation Manual Download Page 125

016-0171-536 Rev. C, E41202

W

e S

ol

ve Gr

ea

t C

ha

lleng

es

.

WHAT IS NOT COVERED BY THE EXTENDED WARRANTY?

Raven Industries will not assume any expense or liability for repairs outside our facility without written consent. Raven 
Industries is not responsible for damage to any associated equipment or products and will not be liable for loss of profit, 
labor, or other damages. The obligation of this warranty is in lieu of all other warranties, expressed or implied, and no 

person or organization is authorized to assume any liability for Raven Industries.

•

Damages caused by normal wear and tear, misuse, abuse, neglect, accident, improper installation and 
maintenance are not covered by this warranty.

•

Worn/Chafed hoses and cables.

•

Items in contact with fluids and chemicals including seals and O-rings.

•

Software downloads and updates.

•

Tamper-Evident label broken or customer disassembly.

•

Any customer modification to the original product outside normal calibration and adjustments, without written 
approval.

•

Intentional modification to cables.

•

Failures due to lack of cleaning or preventive maintenance, and any condition, malfunction or damage not 
resulting from defects in material or workmanship.

•

Items in contact with fluids or chemicals, returned without proper cleaning, decontamination and documentation.

Summary of Contents for RS Lite






























































































































Reviews:

No comments