Raven RS Lite Calibration And Operation Manual Download Page 21

Page: 21 / 125

016-4010-001 Rev. J

CALIBRATION - HDU-SPECIFIC, MD, AND STEERING-READY

FIGURE 9. Wheel Base Page

12. Select the value box to enter the Wheel Base.

NOTE:

The Wheel Base is calculated by measuring from the center of the front tire to the center of the rear

tire on both sides of the machine. Add these measurements together and then divide by two to get

the average Wheel Base value.

13. Select the

Next

arrow.

FIGURE 10. GPS Differential Configuration Page

14. Select the appropriate GPS Differential Source from the drop-down box:
• GL1DE®
• SBAS
• Satellite GS
• RTK

NOTE:

Depending on the number of feature unlocks purchased, all options may not be available for

selection in the drop-down box. Contact your local Raven dealer to purchase additional unlock codes.

15. Select the

Next

arrow.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands