Raven RS Lite Calibration And Operation Manual Download Page 33

Page: 33 / 125

CHAPTER

016-4010-001 Rev. J

CHAPTER 5

MACHINE SETTINGS

FIGURE 1. Machine Settings Page

The Machine Settings page provides access to the machine tunesets and configurations which were entered

during the initial system calibration.

FIGURE 2. Machine Configuration Page

• The Change Profile button allows the user to select an existing tuneset or create a new machine tuneset.
• The Machine Configuration Information button allows the operator to view the profile which was entered

during the calibration process. Settings cannot be changed unless the RS1 system is recalibrated. Press the

Accept button in the lower-right corner of the page to return to the Machine Settings page.

• The Machine Offsets Setup button allows the user to view and adjust the following:

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands