manualshive.com logo in svg

Raven RS Lite, Calibration And Operation Manual, Page: 64 / 125

Share
Download
Raven RS Lite Calibration And Operation Manual Download Page 64

C

HAPTER

 10

58

Raven RS1™ and RS Lite™ Calibration and Operation Manual

DIAGNOSTIC TROUBLE CODES (DTC)

FIGURE 5. Diagnostic Trouble Codes Page

The Diagnostic Trouble Code page displays active and previous diagnostic trouble codes (DTCs) that occur during 

RS1 system operation. Active DTCs must be fixed before the RS1 system can be enabled for guidance and steering 

operation. Once a DTC has been corrected, the code moves to the inactive DTC code list. Refer to Figure 5 on 

page 58 for an example of DTCs and DTC summaries.

Number of Satellites

The number of satellites currently in view by the GPS receiver.

HDOP

Horizontal Dilution of Precision. If all of the satellites in view are from 

the same direction, the number will be higher and the accuracy will be 

reduced.

Age of Differential

Time (in seconds) since the last differential correction was received. If a 

differential source is not currently tracked this entry will be “- - - -”.

Display

Message

Summary of Contents for RS Lite






























































































































Reviews:

No comments