manualshive.com logo in svg

Raven RS Lite, Calibration And Operation Manual

Introducing the Raven RS Lite, a cutting-edge device designed to revolutionize your operations. Ensure optimal performance with our precise Calibration and Operation Manual, available for free download from manualshive.com. Navigate through every feature effortlessly, maximizing your productivity and efficiency with this user-friendly manual. Get yours now!

Share
Download
background image

TABLE OF CONTENTS

016-4010-001 Rev. J

i

Chapter 1 

Important Information..........................................................................................  

1

Safety ...............................................................................................................................................................................

1

Hydraulic Safety ....................................................................................................................................................

2

Electrical Safety .....................................................................................................................................................

2

Touch Screen ..........................................................................................................................................................

2

Recommendations and Best Practices ................................................................................................................

3

Aerials and Signal Interference .......................................................................................................................

3

Hose Routing .........................................................................................................................................................

3

Harness Routing ...................................................................................................................................................

4

Chapter 2 

Introduction.............................................................................................................  

7

System Specifications ................................................................................................................................................

7

RS1 Electrical Rating ...........................................................................................................................................

7

Installation Best Practices .........................................................................................................................................

7

Recommendations ...............................................................................................................................................

8

Point of Reference ...............................................................................................................................................

8

Updates ...........................................................................................................................................................................

8

Chapter 3 

Calibration - HDU-Specific, MD, and Steering-Ready...................................  

9

Introduction ...................................................................................................................................................................

9

RS1 Terms of Use ......................................................................................................................................................

10

GPS and Steering Calibration ..............................................................................................................................

10

GPS Calibration ...................................................................................................................................................

11

Terrain Compensation Calibration .........................................................................................................

15

Steering Calibration .................................................................................................................................................

18

Homologation ....................................................................................................................................................

18

Resume/Disengage Calibration ...................................................................................................................

18

Calibrate the Wheel Angle Sensor (WAS)  ...........................................................................................

19

Calibrate the Machine Steering System ...........................................................................................................

21

Chapter 4 

Steering Home Page............................................................................................ 

25

Chapter 5 

Machine Settings.................................................................................................. 

27

Chapter 6 

Steering Setup....................................................................................................... 

29

Advanced Tuning .....................................................................................................................................................

30

Advanced Tuning (Cont.) ...............................................................................................................................

31

Wheel Control Settings ..........................................................................................................................................

32

Wheel Control Calibration ....................................................................................................................................

33

Guidance Setup Settings .......................................................................................................................................

36

Wheel Angle Sensor Settings ..............................................................................................................................

38

Disengage Settings ..................................................................................................................................................

39

Resetting Calibrated Gains ...................................................................................................................................

40

Operator Presence Sensor ....................................................................................................................................

40

Summary of Contents for RS Lite






























































































































Reviews:

No comments

Related manuals for RS Lite

Campbell CS500 Instruction Manual preview
CS500
Brand: Campbell Pages: 18
Vector 0 Owner'S Manual & Warranty Information preview
0
Brand: Vector Pages: 4
K&K M8700 Manual preview
M8700
Brand: K&K Pages: 8
unios Echo Quick Installation Manual preview
Echo
Brand: unios Pages: 2
Rane SM26 Operating & Service Manual preview
SM26
Brand: Rane Pages: 6
Rane MP 4 Operation Manual preview
MP 4
Brand: Rane Pages: 27
Ranger Products RD-18G Installation And Operation Manual preview
RD-18G
Brand: Ranger Products Pages: 6
Rane SEVENTY Service Manual preview
SEVENTY
Brand: Rane Pages: 88
Haag-Streit AT 900 Instructions For Use Manual preview
AT 900
Brand: Haag-Streit Pages: 21
Waters Xevo TQD Operator'S, Overview And Maintenance Manual preview
Xevo TQD
Brand: Waters Pages: 250
Waters ACQUITY UPLC Overview And Maintenance Manual preview
ACQUITY UPLC
Brand: Waters Pages: 141
Zodiac iAquaLink Quick Start Manual preview
iAquaLink
Brand: Zodiac Pages: 2
Zipper Mowers ZI-DS2V-AKKU Operation Manual preview
ZI-DS2V-AKKU
Brand: Zipper Mowers Pages: 37
Zimmer enPuls User Manual preview
enPuls
Brand: Zimmer Pages: 46
Pani AP 2 Operation Manual preview
AP 2
Brand: Pani Pages: 12
FASTER TOOLS 1579 Instruction Manual preview
1579
Brand: FASTER TOOLS Pages: 19
Emos ZYP0201 Quick Start Manual preview
ZYP0201
Brand: Emos Pages: 8
Oxylitre AP4600 MK3 Series Instructions For Use Manual preview
AP4600 MK3 Series
Brand: Oxylitre Pages: 15

Brands by name

Popular brands

Load more brands