Raven RS Lite Calibration And Operation Manual Download Page 79

Page: 79 / 125

016-4010-001 Rev. J

DIAGNOSTICS AND TROUBLESHOOTING

MACHINE CONTROL EFFORT STEERING TEST

The top of the Machine Test page allows the operator to test the steering system and valve control effort.
1. Enter the test control effort percent in the left or right field.

FIGURE 14. Disengage Switch Test Page

2. Use the blue arrow buttons to manually steer the wheels left or right.
3. Select the ‘X’ in the lower, left corner to return to the Tests tab.

DISENGAGE

Review the disengage switch settings and confirm switch operation and status.

FIGURE 15. Disengage Switch Test Page

NOTE:

Adjust the Disengage Threshold value to test the disengage status based upon steering wheel inputs.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands