Raven RS Lite Calibration And Operation Manual Download Page 88

Page: 88 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

BUTTON DEFINITIONS

The following are common status or mode messages which may occur.

TABLE 1. UT Navigation Buttons

CELLULAR MODEM

FIGURE 2. Cellular Status Page

Accept - Saves changes made to the RS1 system and returns the user to the

previous Status page (or returns the user to the Tools Menu during the initial

setup process).

Next - Press to proceed to the next page.

Previous - Returns the field computer display to the previous page in the setup

process.

Display

Message

RS1 is connected to the network via the cellular modem.

The cellular modem is functional, but is not connected to the network.

The cellular modem is not functional and RS1 is not connected to the network.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands