Raven RS Lite Calibration And Operation Manual Download Page 69

Page: 69 / 125

016-4010-001 Rev. J

DIAGNOSTICS AND TROUBLESHOOTING

5238

Invalid curvature.

1. Check cabling and connections to the steering

partner (steering valve).

2. Cycle power to the steering valve.
3. Update the steering partner/valve software.

.31

Loss of SCU

communication.

The RS1 previously registered a steering partner but is

not currently communicating with the expected partner.
1. Check cabling and connections to the steering

partner (steering valve).

2. Cycle power to the steering valve.
3. Check the software version of the steering partner/

valve and confirm compatibility with the RS1

software.

5241

.31

Disengage switch is in the

off position.

1. Check the disengage switch status in the RS1 UT.

Switch should only be active (red status indicator)

when the steering wheel is moving.

2. If the disengage switch is showing activity (red) while

the steering wheel is stationary, increase the

disengage value. Review the

Resume/Disengage

Calibration

section on page 19. For best results, set

the value as low as possible.

3. Check the disengage switch cabling and

connections.

4. Check the sensor voltage (5 V) and current (4-20

mA). Review the

Disengage Settings

section on

page 39 for assistance with the disengage switch

settings.

5243

Master switch is in the off

position.

1. Toggle the master switch ON or to field mode.
2. Toggle the hydraulic lock switch to the unlocked

state.

3. Check CAN communication to the steering valve.

5613

.11

Field terrain

compensation not

calibrated.

Perform the terrain compensation calibration. Refer to

the

Terrain Compensation Setup

section on page 45.

.13

Terrain compensation not

calibrated.

Perform a terrain compensation calibration. Refer to the

Terrain Compensation Setup

section on page 45.

Inertial navigation system

(INS) data invalid.

1. Perform a terrain compensation calibration. Refer to

the

Terrain Compensation Setup

section on page 45.

2. Verify inertial sensor functionality in the RS1 UT.

.31

GPS receiver error: INS

reset.

Cycle power to the RS1.

516118

.14

Toggle autonomy switch

to the OFF position.

Toggle the autonomy switch to the OFF position.

.17

Autonomy switch in the

OFF position.

1. Toggle the autonomy switch to the ON position.
2. Check switch cabling and connections.

Machine not configured

for automation.

Complete a calibration with autonomous features

enabled. Complete provisioning procedures for

autonomous machine operations.

Code ID

Description

Recommended Actions

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands