Raven RS Lite Calibration And Operation Manual Download Page 74

Page: 74 / 125

HAPTER

Raven RS1™ and RS Lite™ Calibration and Operation Manual

523874

.13

Memory communication

error.

Power cycle the RS1. If the issue persists, contact Raven

technical service.

523875

.13

SCU software out of date. Update the RS1 software.

523875

MCM software

compatibility.

Update Machine Control Module (MCM) software

version.

523898

.31

OEM engage error.

Field computer on-screen engage switch not supported.

Use the machine engage switch to initiate autosteer.

523913

.31

GPS invalid authorization.

Some correction types require an unlock code. Either

the code was not entered correctly or an existing code

has expired.
Review Chapter 8,

Feature Unlock Codes

for additional

information on entering unlock codes. Contact a local

Raven dealer or Raven technical service for additional

support.

523916

.13

SC1 software out of date.

Update the SC1 ECU software version.

.14

RS Lite software out of

date.

Update the RS Lite software version.

523918

GPS receiver error: input

overrun.

Power cycle the RS1.

523919

.31

GPS receiver error:

jammer detected.

523920

GPS receiver error: IMU

communication failure.

523921

.31

GPS receiver error:

tracking mode.

523922

.31

GPS receiver error: digital

filter enabled.

523923

VSN data invalid warning.

VSN is unable to provide valid row guidance. Check the

camera feed and solution quality from the VSN object

pool Home page.

523924

VSN data invalid error.

VSN guidance vectors not valid. Restart the VSN.

523925

No row camera

communication.

VSN times out after 10 seconds. Check cabling and

connections.

523926

.31

No user activity.

Check operator switch settings and operator switch

cabling and connections if present.

523927

.31

VSN only needs TC.

VSN requires a task controller. Open a job on a field

computer to use VSN guidance.

523928

.13

Invalid factory calibration

1. Restart the RS1.
2. Contact your local Raven dealer.

573927

.31

VSN only job required.

Start a job on the field computer or UT to function.

Code ID

Description

Recommended Actions

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Brands by name

Popular brands