Raven RS Lite Calibration And Operation Manual Download Page 106

Page: 106 / 125

HAPTER

100

Raven RS1™ and RS Lite™ Calibration and Operation Manual

ECU UPDATES

1. From the Slingshot working set home page, select the

Diagnostics

button.

2. On the System Information tab, select the RS1 Information option in the drop-down.
3. Select the

ECU Updates

button at the bottom of the page.

FIGURE 24. System Information Page

4. If any updates are available for ECUs connected to the ISOBUS, use the drop-down list at the top of the page to

review version information for each device as desired.

FIGURE 25. ECU Updates Page

5. Select the

Program Selected

button at the bottom of the page to program the specific ECU displayed on the

page. Select the

Program All

button to begin the update process for all ECUs which have updates available.

Summary of Contents for RS Lite





























































































































Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands

Raven RS Lite, Calibration And Operation Manual

Search results

Summary of Contents for RS Lite

Reviews:

Related manuals for RS Lite

Brands by name

Popular brands