Rapiscan AS&E MINI Z Operator'S Manual Download Page 158 | Manualshive

Page: 158 / 276

background image

Advanced Scanning: Annotating Scan Images

American Science and Engineering, Inc.

7-14

MINI

Z

Operator Manual 342-9000-1 Rev. B ECCN EAR99

•

Optionally, to view all of the scans in the current scan group at the same time in a gallery view,

tap the Mode button

to open the Scan screen in Gallery mode (see

Section 5.3, Scan

Gallery Mode Screen

). Tap the

Mode

button

again to return to the Scan Monitor mode

screen.

•

Optionally, to open a Reference image for ongoing comparison to the scans, tap the Back

button to return to the

Home Screen

. and then tap the

Review

button. When the Review screen

opens, tap the Mode button

to change to the Search mode of the Review screen (see

Section 9.4, Searching for Images

). To search for Reference images, in the search criteria (see

Figure 9-8

) select the check box next to the

Reference images

criterion.

•

Ambient lighting conditions between bright and dark rooms and times of day can make it
difficult to view the screen elements on the tablet. It is possible to switch between light and
dark color schemes at any time between performing scans. Using the

Settings

>

General

>

Skins

area, there are two buttons: light background, and dark background.

.

For looking at scan images in particular, another method is to apply the Reverse Video imaging
enhancement in the

Scan Monitor Mode Screen

or

Review View Mode Screen

. The Windows

Action Center

(

Section 3.7.6

) and the tablet Dashboard functions (

Section 11.2

) allow for

changing screen brightness to a limited extent

.

7.5

Annotating Scan Images

7.5.1

Image Physical Correlations

While performing a scan, each time the X-ray beam is started and stopped, a separate image is pro-
duced. The length of the target captured by the image depends on the rate at which the scanner is
moved during the scan, and the duration of time the scanner beam remains turned on. A recommended
rate of scanning is to move the scanner steadily across six inches (15 centimeters) of the scan path per
second of time. The maximum scan time is 30 seconds. This gives a maximum scan image that covers
15 feet (4.5 meters) of linear travel.

The width of the area scanned corresponds roughly to the width of the MINI Z housing, approximately
eight inches (20 centimeters). The width is indicated by the separation of the two laser guide beams. If
the scanner is farther from the target, the width of the target scanned increases in proportion.

The scanned image is a composite of the backscatter of multiple individual bursts of the X-ray beam
cutting across the horizontal plane of the scanner face, between the two laser guide beams. The dis-
tance between each scan, and the relative resolution of the image, is a function of the scan rate at the
time of detection. The individual detection bands are joined to form a continuous image when pro-
cessed by the MINI Z system.

«
...
156
157
158
159
160
...
»

Summary of Contents for AS&E MINI Z





















































































































































































































































































Reviews:

No comments

Related manuals for AS&E MINI Z

Brand: Oemtools Pages: 4

Brand: NEC Pages: 29

Brand: Bante Instruments Pages: 6

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: IEMCA Pages: 82

KID 80-IV Touch

Brand: IEMCA Pages: 122

Brand: Calrec Pages: 92

Brand: OHAUS Pages: 84

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

Smart Plus PHT-35LHS

Brand: Vatech Pages: 190

Brand: Yamaha Pages: 48

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Brand: SAC Pages: 2

Brand: Eaton Pages: 38

Brand: Bison Pages: 4

Brand: Conductix-Wampfler Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands