Q2 Q2A, Technical Manual

Page: 201 / 866

Standards
Compliance
5
5.3 UL Standards
SIEPYEUOQ2A01G AC Drive Q2A Technical Manual 201
Table 5.10 Recommended Wiring Tools
Screw Adapter
Bit
Torque Driver Model
(Tightening Torque)
Torque Wrench
Model Manufacturer
M4
Bit SF-BIT-SL 1,0X4,0-70 PHOENIX CONTACT
TSD-M 3NM
(1.2 - 3 N∙m)
-
M5
*1
Bit SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
Wire Gauge ≤ 25 mm 2 (AWG 10):
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge ≤ 25 mm 2 (AWG 10):
-
Wire Gauge ≥ 30 mm
2
(AWG 8):
-
Wire Gauge ≥ 30 mm
2
(AWG 8):
4.1 - 4.5 N∙m
*2 *3
M6
Bit SF-BIT-HEX 5-50 PHOENIX CONTACT - 5 - 9 N∙m
*2 *3
M6
Bit SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT - 3 - 3.5 N∙m
*2 *3
M8
Bit SF-BIT-HEX 6-50 PHOENIX CONTACT - 8 - 12 N∙m
*2 *3
M10
Bit SF-BIT-HEX 8-50 PHOENIX CONTACT - 12 - 14 N∙m
*2 *3
*1 When wiring drive models 2056 and 4089 and smaller, select the correct tools for the wire gauge.
*2 Use 6.35 mm (0.25 in) bit socket holder.
*3 Use a torque wrench that can apply this torque measurement range.
■
Wire Gauges and Tightening Torques as Specified by UL Standards
Comply with local standards for correct wire gauges in the region where the drive is used.
WARNING! Electrical Shock Hazard. Only connect peripheral options, for example a DC reactor or braking resistor, to terminals
+1, +2, +3, -, B1, and B2. Failure to obey can cause death or serious injury.
Refer to Notes on Wire Gauges and Tightening Torques on page 77 for general conditions
Drives from model 2257 and from model 4208, use UL-approved closed-loop crimp terminals on the drive main
circuit terminals. Use the tools recommend by the terminal manufacturer and make sure that the terminals are
correctly connected.
Select the correct wires for main circuit wiring.
Three-Phase 200 V Class
Model Terminal
Recomm. Gauge
AWG, kcmil
Applicable Gauge
AWG, kcmil
(mm 2 )
IP20 Applicable
Gauge
*1
AWG, kcmil
(mm
2
)
Wire Stripping
Length
*2
mm
Terminal Screw
Size and Shape
Tightening
Torque
N
∙
m (lbf
∙
in)
2004
R/L1, S/L2, T/L3 14
14 - 6
(2.5 - 16)
14 - 6
(2.5 - 16)
10
M4
1.5 - 1.7
(13.5 - 15)
U/T1, V/T2, W/T3 14
14 - 6
(2.5 - 16)
14 - 6
(2.5 - 16)
10
M4
1.5 - 1.7
(13.5 - 15)
-, +1, +2 14
14 - 3
(2.5 - 25)
14 - 3
(2.5 - 25)
18
M5
2.3 - 2.5
(19.8 - 22)
*3
B1, B2 14
14 - 10
(2.5 - 6.0)
14 - 10
(2.5 - 6.0)
10
M4
1.5 - 1.7
(13.5 - 15)
10
14 - 8
(2.5 - 10)
- -
M4
1.2 - 1.5
(10.6 - 13.3)
2006
R/L1, S/L2, T/L3 14
14 - 6
(2.5 - 16)
14 - 6
(2.5 - 16)
10
M4
1.5 - 1.7
(13.5 - 15)
U/T1, V/T2, W/T3 14
14 - 6
(2.5 - 16)
14 - 6
(2.5 - 16)
10
M4
1.5 - 1.7
(13.5 - 15)
-, +1, +2 14
14 - 3
(2.5 - 25)
14 - 3
(2.5 - 25)
18
M5
2.3 - 2.5
(19.8 - 22)
*3
B1, B2 14
14 - 10
(2.5 - 6.0)
14 - 10
(2.5 - 6.0)
10
M4
1.5 - 1.7
(13.5 - 15)
10
14 - 8
(2.5 - 10)
- -
M4
1.2 - 1.5
(10.6 - 13.3)