Prusa Research Original Prusa SL1 Manual Download Page 71

Page: 71 / 92

4. Electronics & Lid

Original Prusa SL1 kit assembly

STEP 40

Inserting the torx screws

Check the holes in the frame and in the foil are aligned.

DON'T PUNCH

through new holes for the Torx screws!

Start inserting the remaining screws.

Don't push hard

, or you might bend the

frame.
Check you have used twenty-two M4x8rt Torx screws.
Prepare the resin tank, place it on a flat surface with the bottom facing up.

STEP 41

Assembling the resin tank

Place the frame with the film and screws on the tank and start tightening M4x8rt

screws with the Torx tool. Follow the indicated direction, tighten one by one.

Screw

them only halfway in!

Reseat the parts if needed and tighten the screws, this time just near the surface.

Final tightening of the screws, but

BE CAREFUL

. If the Torx tool slips, you might

damage your FEP film.

Pro tip: Turn the tank upside down to its "normal position" and fill it with tap water

to its max level. Watch the tank and ensure no water is leaking.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands