Prusa Research Original Prusa SL1 Manual Download Page 18

Page: 18 / 92

2. Base & Tower

Original Prusa SL1 kit assembly

STEP 9

Tower and PSU parts preparation

For the following steps, please prepare:

Bottom plate (1x)
Support (2x)
M3x8 screw (8x)
Adjustable foot (4x)
Don't install any foot before being told to, you would block yourself access to some

screws.

STEP 10

Mounting the bottom plate

Before we connect the bottom plate to the rest of the printer, let's find the groove,

which will be used to align both parts together.
Lift and slightly slide the current assembly to the edge of the cardboard to get

access to the lower edge of the back plate. Keep some space for adding the bottom

plate.
Place the side of the bottom plate with the groove on the back plate. Make sure

both parts are aligned properly and no wires are pinched.
Secure both parts together using four M3x8 screws.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands