Prusa Research Original Prusa SL1 Manual Download Page 29

Page: 29 / 92

2. Base & Tower

Original Prusa SL1 kit assembly

STEP 31

Tilt parts preparation

For the following steps, please prepare:

Tilt assembly (1x)
M3x8 screw (8x)
M3w washer (1x)
M3nN nyloc nut (1x)

STEP 32

Mounting the tilt assembly

First, make sure the cantilever is close to the top of the tower. You will need space

to flip the tilt assembly in.
Pull the connecting rod outside the printer and slide the tilt assembly on the pin, all

the way in. Both parts have to be in direct contact.
Carefully flip the tilt assembly on the printer and check the following:

The tilt assembly is properly aligned with the edge of the back plate.
No wire is pinched.
The tilt assembly fits "around" the tower.
The tilt assembly fits on top of both supports.

After the tilt assembly is properly seated, secure it using eight M3x8 screws.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands