Prusa Research Original Prusa SL1 Manual Download Page 19

Page: 19 / 92

2. Base & Tower

Original Prusa SL1 kit assembly

STEP 11

Mounting the supports

Before you mount the support, please take a closer look at:
The bottom plate, which has two special grooves for the supports. The picture is

showing just one, the second is on the opposite side and completely identical.
Each support has two holes with countersink from one side, this side has to be

facing outwards from the printer.
The other side of the support is without countersink and must be facing inwards to

the printer.
All the holes are symmetrical, therefore apart from the countersink holes, you can

rotate them either way.
Take the first support and mount it to the bottom plate. Ensure the countersink

holes are facing outwards, then secure the support using two M3x8 screws from

the bottom.
Check the bottom plate and support outer surfaces are aligned. If not, release the

screws a little bit and readjust the support. Then tighten the screws again.
Continue in the next step...

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands