Prusa Research Original Prusa SL1 Manual Download Page 16

Page: 16 / 92

2. Base & Tower

Original Prusa SL1 kit assembly

STEP 5

Arranging the back plate

Due to the safety reasons, the back plate is rotated during the transport. Let's rotate

it back to the "assembly position".
Flip the back plate 180 °. The notch must be facing up.
The correct position of the back plate for the assembly. Make sure the "notch" is

facing up.

STEP 6

Connecting the tower

WARNING:

Proper assembly of the tower is SUPER CRUCIAL. If you misalign the

tower, you will have issues with the prints.

Follow the instructions and use the

included cardboard!

First, place the tower on the back plate like in the picture. See the four holes on

both parts, which have to match each other.
Rotate the tower on the back plate, then align the holes and insert two screws

M4x8 in the lower row.

Don't tighten them yet!

Push the tower

DOWN

and to the

RIGHT

and then tighten:

First the screw on the left
Second the screw on the right

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands