Prusa Research Original Prusa SL1 Manual Download Page 69

Page: 69 / 92

4. Electronics & Lid

Original Prusa SL1 kit assembly

STEP 35

Assembling the cover

Slide the cover on the printer and secure it on one side using two M3x5b

countersunk screws. Don't tighten them firmly and move on the other side, repeat

the procedure.
As soon as the cover is aligned and partly secured, add the remaining screws and

tighten them all.
Tighten carefully, if you can't reach the holes in the printer, realign the cover.

STEP 36

Preparing resin tank parts

For the following steps, please

prepare:

Resin tank (1x)
Resin tank frame (1x)
Resin tank screw (2x)
M4x8rt Torx screw (22x)
FEP film (1x)

STEP 37

Preparing the resin tank frame

Take the resin tank frame

(orientation doesn't matter) and

push through four M4x8rt Torx

screws in the corners.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands