Prusa Research Original Prusa SL1 Manual Download Page 57

Page: 57 / 92

4. Electronics & Lid

Original Prusa SL1 kit assembly

STEP 10

Preparing the touchscreen parts

For the following steps, please prepare:

Touchscreen assembly (1x)
M4x10 screw (2x)
You can peel off the protective film, but keep that in mind and avoid scratching it

during the assembly of the surrounding parts.

Be careful with all the cables while assembling

the touchscreen. Make sure none

gets pinched or bent.

STEP 11

Mounting the touchscreen assembly

Take a look from below the printer to find two holes in the tilt assembly. We will

use them to mount the touchscreen.
Place the touchscreen in the printer and secure it using two M4x10 screws.
Note: The touchscreen assembly contains three cables: for the touchscreen, then

Wi-Fi antenna and a speaker.

Handle them with care!

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands