Prusa Research Original Prusa SL1 Manual Download Page 64

Page: 64 / 92

4. Electronics & Lid

Original Prusa SL1 kit assembly

STEP 24

Inserting the print display in the printer

WARNING:

make sure the cable leading from the print display is not bent or

pinched before you tighten the screws. Always ensure the cable is alright.

DON'T PEEL OFF THE PROTECTIVE FILM!

Wait for the instructions!

Carefully insert the LCD assembly in the printer

, like in the picture. Make sure the

cable is

ON THE LEFT

side and not bent.

Carefully lay the assembly down, make sure it is aligned with the printer.

STEP 25

Fixing the display in place

Use the M4x14b countersunk screws to fix the LCD back in place. Don't tighten

them, first make sure the LCD is seated properly.
Now, tighten all 10 screws firmly, but with a reasonable force. You might strip the

screw.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands