Prusa Research Original Prusa SL1 Manual Download Page 46

Page: 46 / 92

3. Covers & Platform

Original Prusa SL1 kit assembly

STEP 26

Print platform part preparation

ALWAYS PROTECT

the surface of

the print platform, use a Microfiber

cloth or similar soft fabric (not

included in the kit).

For the following steps, please

prepare:

Print holder (1x)
Print platform (1x)
M4x10 screw (4x)

STEP 27

Assembling the platform

Pay attention

to the correct orientation of the parts, before you use the screws to

connect them together.

The

incorrect assembly

the groove is visible (facing up)

The

correct assembly

the groove is hidden (facing down)

Make sure the edges of both parts are aligned. In this plane, the part can be rotated

180 ° (its orientation doesn't matter).
Secure both parts using M4x10 screws.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands