Prusa Research Original Prusa SL1 Manual Download Page 48

Page: 48 / 92

3. Covers & Platform

Original Prusa SL1 kit assembly

STEP 30

Mounting the eccentric

WARNING:

This step involves inserting parts from below and it might be slightly

more difficult. You can lay the printer on its back, but use the cardboard to protect

the PSU power button.

Look from below the cantilever, check the two holes for the screws.
Insert the eccentric and hold it.
Use two M4x8 screws to secure it. The eccentric will be still able to wobble, but

won't fall down.
We will tighten the screw(s) in the cantilever later on during the calibration process.

STEP 31

Assembling the knob

Slide the M8x45 screw in the printed part. The top surface of the screw should be

flush with the surface of the printed part.
Close the assembly using the cover. Make sure both parts are aligned. If not, the

screw isn't properly seated inside.
Screw slightly the "knob" assembly in the printer.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands