Prusa Research Original Prusa SL1 Manual Download Page 21

Page: 21 / 92

2. Base & Tower

Original Prusa SL1 kit assembly

STEP 15

Preparing the tilt motor parts

For the following steps, please prepare:

Tilt motor (1x)
Tilt motor holder (1x)
M3x10 screw (4x)
M4x8 screw (2x)
M3x5 screw (2x)
Optical IR-sensor (1x) can be black or red, functionality is the same
The list continues in the next step...

STEP 16

Preparing the tilt motor parts

For the following steps, please prepare:

Connecting rod (1x)
Optical sensor cable (1x)

The connectors of the optical sensor cable differ in wiring!

Make sure you follow

the instructions and connect it correctly!

The side marked with the red arrow

must

be connected to the optical sensor.

There are two versions of the connecting rod. They differ in the manufacturing

process, assembly is the same.

Summary of Contents for Original Prusa SL1





























































































Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands

Prusa Research Original Prusa SL1, Manual

Search results

Summary of Contents for Original Prusa SL1

Reviews:

Related manuals for Original Prusa SL1

Brands by name

Popular brands