Nikon NPL-302 Series Instruction Manual Download | Manualshive

Page: 33 / 234

background image

Preparation

2

Pulse Laser Station NPL-302 Series Instruction Manual

13

Discharging the battery pack

1.

Connect the power plug on the charger to an AC power outlet.

2.

Connect the charging plug on the charger cable to the charging connector on the
battery pack.

3.

Press the DISCHARGE button on the battery charger.

The DISCHARGE indicator lights up, and the charger starts to discharge the
battery. When discharging is completed, the DISCHARGE indicator turns off.
Then the CHARGE indicator lights up, and charging starts automatically.

To stop discharging the battery pack, press the DISCHARGE button again.

Note –

The battery pack can be recharged repeatedly. If you recharge the battery

pack while it still has enough power to operate the instrument, however, it will last
for a shorter period. This is called the

memory effect

. If you experience the memory

effect, discharge the battery pack as described above and then recharge it. This
returns the battery pack to its full capacity. We recommend that you discharge the
battery pack in this way at least once every ten charges.

Detaching and Re-Attaching the Battery Pack

2.1

Detaching the BC-65 battery pack

1.

If the instrument is turned on, press

[PWR]

to turn it off.

2.

Depress the battery mounting button while holding the battery pack.

C

Caution –

Avoid touching the contacts on the battery pack.

«
...
31
32
33
34
35
...
»

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

Brand: Banner Pages: 11

Brand: Bante Instruments Pages: 10

Brand: BANTE Pages: 11

Brand: Banner Pages: 14

Brand: Banner Pages: 16

Brand: Kane Pages: 16

Brand: Kane Pages: 60

Brand: Taber Pages: 53

Brand: NCTE Pages: 10

Brand: QUNDIS Pages: 20

Brand: R&S Pages: 2

Brand: Panasonic Pages: 1

Brand: Stübbe Pages: 12

Brand: Vaisala Pages: 40

Brand: ProsKit Pages: 10

Brand: TQC Sheen Pages: 16

Brand: AEMC Pages: 20

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands