Nikon NPL-302 Series Instruction Manual Download | Manualshive

Page: 22 / 234

background image

1

Introduction

2

Pulse Laser Station NPL-302 Series Instruction Manual

Welcome

1.1

Thank you for purchasing this Nikon product.

This instruction manual was written for the users of Pulse Laser Station NPL-302
series instruments. Before you operate a Pulse Laser Station NPL-302 series
instrument, read this manual carefully. In particular, pay attention to the warnings
and cautions that appear in the Safety section at the front of the manual. Before you
begin, you should also read the maintenance instructions. For more information, see
Maintenance, page 6.

Instrument accuracy and display

11.1

One of the benefits of the Nikon DTM-302, NPL-302, and DTM-502 series
products is ease-of-use. The software for these three product series has been
designed to make it easy for you to learn to operate one model of instrument and
apply that knowledge to the other models with little additional training. A
DTM-302 series user can easily operate the non-prism NPL-302 series instruments
or the higher accuracy DTM-502 series instruments.

There are some subtle differences in the software between these different product
families. Some of these differences stem from additional capabilities or features
available in some models. For example, the DTM-502 series offers the Lumi-Guide
functionality, which guides the rodman to the correct stake-out position quickly and
easily. The NPL-302 series offers reflectorless operation, allowing you to take
measurements to points inaccessible with a prism. This manual shows the unique
capabilities and features available in the NPL-302 series instrument.

«
...
20
21
22
23
24
...
»

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

Brand: AccuMASTER Pages: 2

Brand: OHAUS Pages: 84

Brand: National Instruments Pages: 15

Brand: Yamaha Pages: 48

Brand: Kawai Pages: 64

Brand: Kawai Pages: 28

Brand: Kawai Pages: 28

Brand: Endress+Hauser Pages: 88

Brand: Stübbe Pages: 12

Brand: ADA INSTRUMENTS Pages: 27

Brand: BizLine Pages: 62

Brand: Bahco Pages: 21

Brand: Kübler Pages: 72

Brand: Cable Ferret Pages: 16

Brand: Omega Pages: 24

Lange ORBISPHERE 3100

Brand: Hach Pages: 47

Brand: Draminski Pages: 22

Ophir Spiricon BeamWatch Standard

Brand: MKS Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands