manualshive.com logo in svg

Nikon NPL-302 Series, Instruction Manual

The Nikon NPL-302 Series, a cutting-edge surveying instrument, combines accuracy and reliability. To operate it with ease, make sure to download the comprehensive Instruction Manual available for free on our website. Unlock the full potential of your Nikon NPL-302 by accessing the user manual at manualshive.com.

Share
Download
background image

Menu Key   

5

Pulse Laser Station NPL-302 Series Instruction Manual   

147

Deleting station records

In the Station screen, use 

[^]

 or 

[v]

 to highlight the 

record that you want to delete. Then press the 

DEL

 softkey.

A confirmation screen appears.

Press 

[ENT]

 or the 

Yes

 softkey to delete the 

selected record.

A reconfirmation screen appears. Press the 

DEL

 

softkey to confirm deletion.

There is no undelete function on the instrument. 
Before you press the 

DEL

 softkey, make sure that 

you have selected the correct station record. You 
cannot press 

[ENT] 

in this screen.

You can also delete coordinate data by pressing 
the 

DEL

 softkey in the detailed display screen for 

the record.

If the record that you want to delete is referred by 
an ST record, a confirmation message appears.

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

A&D SV-1A Instruction Manual preview
SV-1A
Brand: A&D Pages: 102
UEi MCP9A Instruction Manual preview
MCP9A
Brand: UEi Pages: 5
Seben 69003 Instruction Manual preview
69003
Brand: Seben Pages: 16
BYK micro-TRI-gloss ? Operating Instructions Manual preview
micro-TRI-gloss ?
Brand: BYK Pages: 174
Supertech agroline Superpro Combi Instruction Manual preview
Superpro Combi
Brand: Supertech agroline Pages: 10
Zareba Intelligizer Fence Monitor User Manual preview
Intelligizer Fence Monitor
Brand: Zareba Pages: 8
National Instruments NI PXIe-4139 Calibration Procedure preview
NI PXIe-4139
Brand: National Instruments Pages: 24
D-tect Systems rad-DX Getting Started Manual preview
rad-DX
Brand: D-tect Systems Pages: 2
WAGNER Datamaster Quick Start Manual preview
Datamaster
Brand: WAGNER Pages: 4
Radians Innova EnviroMentor Field Finder User Instructions preview
EnviroMentor Field Finder
Brand: Radians Innova Pages: 12
Parkside 315778 1904 Operation And Safety Notes preview
315778 1904
Brand: Parkside Pages: 165
Velleman DVM401 Manual preview
DVM401
Brand: Velleman Pages: 18
Ress SK7 Manual preview
SK7
Brand: Ress Pages: 11
ATIM ACW/LW8-TM0P User Manual preview
ACW/LW8-TM0P
Brand: ATIM Pages: 32
Kobold Heinrichs TSK Installation And Operating Instructions Manual preview
Heinrichs TSK
Brand: Kobold Pages: 27
South GALAXY G7 User Manual preview
GALAXY G7
Brand: South Pages: 54
Anritsu MP1632C Operation Manual preview
MP1632C
Brand: Anritsu Pages: 127
RADWAG PUE HX7 Quick Start Manual preview
PUE HX7
Brand: RADWAG Pages: 12

Brands by name

Popular brands

Load more brands