Nikon NPL-302 Series Instruction Manual Download

Page: 49 / 234

Getting Started

Pulse Laser Station NPL-302 Series Instruction Manual

Turning off the instrument

30.1

To turn the instrument off, press

[PWR]

and

[ENT]

Then do one of the following:

Sleep mode

If you press the

Sleep

softkey in the Press

[ENT]

→

OFF screen, or enable the Power Save setting

(see Power saving, page 138), the instrument goes
into sleep mode.

When the instrument is in sleep mode, it wakes up
if any of the following occurs:

• You press a key

• The instrument receives a remote control command

• You rotate the alidade

• You tilt the telescope

Press ...

To ...

[ENT]

again

turn off the instrument

the

Reset

softkey

reboot the program and re-start the instrument

the

Sleep

softkey

put the instrument into power-saving mode

[ESC]

cancel the power-off process and return to the
previous screen

If you press the

Reset

softkey, the software is rebooted and the Basic

Measurement Screen (BMS) appears without an open job.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands