Nikon NPL-302 Series Instruction Manual Download

Page: 114 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

Using

[DSP]

to switch between display screens

Press

[DSP]

to switch between the Stakeout display screens. The following screens

are available:

The ARC5 screen is only available if the secondary distance unit is set. For more
information, see Others settings, page 140.

Every time you press

[DSP]

, the next screen appears. If you press

[DSP]

in the last

screen (ARC4 or ARC5), the ARC1 screen appears.

To record the point, press

[ENT]

on any observation

screen. The arc is stored in comment records.

Sample records

CO,Arc P1:583  AZ1=0.0000  P2:102
CO,    AZ2=311.2932 Radius=50.0000  Length=125.6637
CO,    Sta=  -12.6876 Offset=    1.3721 dZ=   0.0971
SS,17,1.0000,6.9202,18.4700,80.3120,15:48:48,2REF-LINE

ARC1

ARC2

ARC3

ARC4

Sta
O/S

X
Y
Z

HA
VA
SD

HA
VD
HD

ARC5

HD
VD
SD

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands