Nikon NPL-302 Series Instruction Manual Download

Page: 160 / 234

Menu Key

140

Pulse Laser Station NPL-302 Series Instruction Manual

Others settings

51.9

To open the Others menu, press

[9]

or select

Other

in the Settings menu.

XYZ disp Fast/Norm/Slow/+ENT

Defines speed to move to the next
screen after showing XYZ of the
input PT

2nd Unit

None/Meter/US-Ft/I-Ft

When the Secondary unit is set to a unit, an extra display screen is
available in the BMS, stakeout observation screens, and 2-pt
reference line screens. The extra screen shows the HD, VD, and SD
in the secondary unit.

Sig Beep ON/OFF

Split ST

No/Yes

Select Yes to separate the point numbers of station points from other
record type point numbers.

CD Input ABC/123

Sets the default input mode when a CD field appears.

If you select US-Ft or I-Ft, an additional settings
screen appears. Use this screen to specify
whether to display values in Decimal-Ft or Ft-
Inch.

If you set the Split ST field to Yes, an additional
setting screen appears. Use this screen to specify
the starting ST number.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands