Nikon NPL-302 Series Instruction Manual Download

Page: 124 / 234

Applications

104

Pulse Laser Station NPL-302 Series Instruction Manual

Outputting data to the COM port

41.2

If you press

[ENT]

while the

[COM]

icon appears in

an observation screen, a line of data is output to
the COM port.

Note –

[COM]

appears, data is

not

stored to the job when you press

[ENT]

The format of the output data is defined by the
setting of the Ext.Comm field in

MENU >

Settings > Comm

. For more information, see

Communications, page 138.

Sample output records through COM port

When the Ext.Comm field is set to NIKON:
TR PN: PT8 SD:000066626 HA:003856010 VA:008048500 HT:0000061757
(TR PN: point name SD HA VA HT; when ACK is returned, PN is incremented.)

When the Ext.Comm field is set to SET:
0006662 0804806 0394324 97
(SD VA HA Chk-SUM)

To output data on the COM port when you press

[ENT]

, set the Data Rec field in

MENU >

Settings > Rec

to COM. For more

information, see Recording, page 139.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands