Nikon NPL-302 Series Instruction Manual Download

Page: 158 / 234

Menu Key

138

Pulse Laser Station NPL-302 Series Instruction Manual

Coordinate

51.3

To open the Coordinate menu, press

[3]

or select

Coord.

in the Settings menu.

Order

NEZ/ENZ

Label

XYZ/YXZ/NEZ(ENZ)

North/South

Power saving

51.4

To open the Power Save menu, press

[4]

or select

PwrSave

in the Settings menu.

Main Unit

OFF/5min/10min/30min

EDM Unit

OFF/At Once/0.1min/
0.5min/3min/10min

Sleep

OFF/1min/3min/5min

Communications

51.5

To open the Communication menu, press

[5]

select

Comm.

in the Settings menu.

Ext.Comm

NIKON/SET

Baud

1200/2400/4800/9600/
19200/38400bps

Length

7/8

Parity

EVEN/ODD/NONE

Stop bit

1/2

Stakeout

51.6

Press

[6]

or select

Stakeout

in the Settings

menu to open the Stakeout menu.

Add PT

Integer between 1 and
999,999

The Order and AZ job settings cannot be changed once a job is created.

This field sets the default point number to record observed data in stakeout.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands