manualshive.com logo in svg

Nikon NPL-302 Series, Instruction Manual

The Nikon NPL-302 Series, a cutting-edge surveying instrument, combines accuracy and reliability. To operate it with ease, make sure to download the comprehensive Instruction Manual available for free on our website. Unlock the full potential of your Nikon NPL-302 by accessing the user manual at manualshive.com.

Share
Download
background image

5

   Menu Key

158  

 Pulse Laser Station NPL-302 Series Instruction Manual

The point name is added to the current layer and 
the list is updated.

Adding a code

In the code list, press the 

Add

 softkey to add a 

new feature code to the current layer.

Enter the feature code in the CD field. Press 

[MODE]

 to change between alphabetic and numeric 

input mode.

You can use the REC field to define a numeric 
identifier for each feature code. This is optional: If 
there is a value in the REC field, this value is 
stored. If you leave the REC field blank, the CD 
value is stored.

Press 

[ENT]

 to add the new code and update the 

code list

.

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

Bacharach PCA 2 Instruction, Operating & Maintenance preview
PCA 2
Brand: Bacharach Pages: 60
Bacharach HGM-MZ Product Bulletin preview
HGM-MZ
Brand: Bacharach Pages: 4
Bacharach HGM-MZ Maintenance And Troubleshooting Manual preview
HGM-MZ
Brand: Bacharach Pages: 17
janitza UMG 96-S2 Quick Manual preview
UMG 96-S2
Brand: janitza Pages: 6
janitza UMG 804 Installation Manual preview
UMG 804
Brand: janitza Pages: 36
YOSensi Airflow Pro2 Quick Installation Manual preview
Airflow Pro2
Brand: YOSensi Pages: 3
janitza UMG 96RM-P Operating Instructions And Technical Data preview
UMG 96RM-P
Brand: janitza Pages: 128
Bacharach SF6 Portable Monitor Specifications preview
SF6 Portable Monitor
Brand: Bacharach Pages: 2
Johnson & Associates GSM-500 Operation & Maintenance Manual preview
GSM-500
Brand: Johnson & Associates Pages: 33
PCE Health and Fitness PCE-TG1XX Manual preview
PCE-TG1XX
Brand: PCE Health and Fitness Pages: 11
Parker SensoControl Serviceman SCM-150 Series Operating Instructions Manual preview
SensoControl Serviceman SCM-150 Series
Brand: Parker Pages: 39
OHAUS STARTER 3100C Instruction Manual preview
STARTER 3100C
Brand: OHAUS Pages: 84
Ntron Microx Online User Instruction Manual preview
Microx Online
Brand: Ntron Pages: 29
Hanna Instruments HI 93723 Instruction Manual preview
HI 93723
Brand: Hanna Instruments Pages: 2
Badger Meter American AL-1000 Installation & Operation Manual preview
American AL-1000
Brand: Badger Meter Pages: 16
RS PRO SLM 1353M Instruction Manual preview
SLM 1353M
Brand: RS PRO Pages: 41
SBS SBS-600 Quick Start Manual preview
SBS-600
Brand: SBS Pages: 17
E+E Elektronik HUMIPORT 10 Manual preview
HUMIPORT 10
Brand: E+E Elektronik Pages: 48

Brands by name

Popular brands

Load more brands