Nikon NPL-302 Series Instruction Manual Download

Page: 120 / 234

Applications

100

Pulse Laser Station NPL-302 Series Instruction Manual

Enter a value in the PT and CD fields. Press

[ENT]

Enter the second point on the vertical plane.
Press

[ENT]

Once the plane is defined, the calculated Sta and
dZ values are updated as you move the telescope.
No distance measurement is required.

Sta

Horizontal distance from P1 to the
target point along the baseline

Vertical distance from P1 to the target
point

Using

[DSP]

to switch between display screens

Press

[DSP]

to switch between the plane display screens. The following screens are

available:

Every time you press

[DSP]

, the next screen appears. If you press

[DSP]

in the last

screen (PLN3), the PLN1 screen appears.

To record the point, press

[ENT]

on any screen (V-

PLN1/3 to V-PLN3/3).

Enter PT and CD. Then press

[ENT]

Sample records

CO,Vertical Ref Plane Pt1:516-A1 Pt2:530
CO,Sta=68.021 dz=17.459
SS,30123-A48,1.5480,16.4020,40.4720,89.0730,14:22:47,

PLN1

PLN2

PLN3

Sta

X
Y
Z

HA
VA

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands