Nikon NPL-302 Series Instruction Manual Download

Page: 79 / 234

Getting Started

Pulse Laser Station NPL-302 Series Instruction Manual

When a reflected lightwave is detected, the signal level is
indicated.

Measuring distances

31.2

To take a distance measurement, press

[MSR1]

[MSR2]

in the Basic Measurement Screen (BMS) or

in any observation screen.

While the instrument is taking a measurement, the
prism constant appears in a small font.

If the average count is set to 0, measurements are
taken continuously until you press

[MSR1]

[MSR2]

[ESC]

. Each time a measurement is taken, the

distance is updated.

If the average count is set to a value from 1 to 99,
the averaged distance appears after the last shot.
The field name SD changes to SDx to indicate the
averaged data.

Sighting a tiltable single prism

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands