Nikon NPL-302 Series Instruction Manual Download | Manualshive

Page: 27 / 234

background image

Introduction

1

Pulse Laser Station NPL-302 Series Instruction Manual

7

• To clean the optical lenses, lightly wipe them with a soft cloth or a lens tissue

that is moistened with alcohol.

• The reticle plate cover has been correctly

mounted. Do not release it or subject it to
excessive force to make it watertight.

• Before attaching the battery pack, check

that the contact surfaces on the battery
and instrument are clean. Press the
battery pack into place until the battery-
mounting button rises up to the battery
pack top surface. If the battery pack is not
attached securely, the instrument is not
watertight.

• Press the cap that covers the data output/external power input connector

terminal until it clicks into place. The instrument is not watertight if the cap is
not attached securely, or when the data output/external power input connector is
used.

• The carrying case is designed to be watertight, but you should not leave it

exposed to rain for an extended period. If exposure to rain is unavoidable, make
sure that the carrying case is placed with the Nikon nameplate facing upward.

• The BC-65 battery pack contains a Ni-MH battery. When disposing of the

battery pack, follow the laws or rules of your municipal waste system.

• The instrument can be damaged by static electricity from the human body

discharged through the data output/external power input connector. Before
handling the instrument, touch any other conductive material once to remove
static electricity.

Reticle plate cover

«
...
25
26
27
28
29
...
»

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

Brand: Yamaha Pages: 3

Brand: Yamaha Pages: 69

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: Rayjet Pages: 81

Brand: Oakton Pages: 16

Brand: jenway Pages: 52

Brand: LumaSense Pages: 23

Brand: RIDGID Pages: 18

Brand: WIKA Pages: 88

Brand: SANKO Pages: 97

Brand: Staco Energy Pages: 2

AS-i CompactModule M8

Brand: IFM Pages: 4

Brand: THE ELECTRON MACHINE CORPORATION Pages: 32

HydroTracer FLV HT2

Brand: aboni Pages: 48

Brand: Panametrics Pages: 224

ISOLGUARD HIG93

Brand: hakel Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands