Nikon NPL-302 Series Instruction Manual Download

Page: 146 / 234

Menu Key

126

Pulse Laser Station NPL-302 Series Instruction Manual

If you enter a new point name, you can enter new
coordinates and record the point. If you do not
want to record the point, press

[ENT]

without

entering a value in the PT field. An XY coordinate
input screen appears.

Continue to enter points until you have defined all
the points in the lot. Then, press

[v]

to calculate the

area and perimeter.

Press

[ENT]

to store the calculated values as a

comment record, or press

[ESC]

to return to the

Cogo menu.

If you chose to store the area, enter a name to
identify the area and then press

[ENT]

The first and last points that you enter are joined to close the area.
You must enter the points in the order in which they define the lot.
You can enter up to 99 points.

When you download data in Nikon RAW format, area (AR) records are output as
comment (CO) records.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands