Nikon NPL-302 Series Instruction Manual Download

Page: 116 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

Measuring between the current and the first point measured

To enter the RDM (Radial) function, press

[3]

or select

RDM(Radial)

in the Programs

menu.

Sight the first point and press

[MSR1]

[MSR2]

The distance from the station point to the first
point appears.

Sight the second point and press

[MSR1]

[MSR2]

. The distances between the first and

second point are displayed.

rSD

Slope distance between two points

rVD

Vertical distance between two points

rHD

Horizontal distance between two points

To change display screens, press

[DSP]

rAZ

Azimuth from first point to second point

rV%

Percentage of grade (rVD/rHD) × 100%

rGD

Vertical grade (rHD/rVD): 1

To record the distance and angle information
as a comment record, press

[ENT]

in the 1/2 or

2/2 observation screen.

Default point numbers are displayed. You can
change these point numbers. To record a note,
press

[ENT]

in the To field.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands