Nikon NPL-302 Series Instruction Manual Download

Page: 111 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

Sight the prism or reflective sheet and press

[MSR1]

[MSR2]

Sta

Horizontal distance from P1 to the
measure point along the P1-P2 line

O/S

Horizontal offset from the P1-P2 line to the measured point

Vertical offset from the P1-P2 line to the measured point

Using

[DSP]

to switch between display screens

Press

[DSP]

to switch between the Stakeout display screens. The following screens

are available:

The REF5 screen is only available if the secondary distance unit is set. For more
information, see Others settings, page 140.

Every time you press

[DSP]

, the next screen appears. If you press

[DSP]

in the last

screen (REF4 or REF5), the REF1 screen appears.

REF1

REF2

REF3

REF4

Sta
O/S

X
Y
Z

HA
VA
SD

HA
VD
HD

REF5

HD
VD
SD

Plain view

Side view

PT1

PT2

Sta

O/S

Prism

PT2

Sta

PT1

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands