manualshive.com logo in svg

Nikon NPL-302 Series, Instruction Manual

The Nikon NPL-302 Series, a cutting-edge surveying instrument, combines accuracy and reliability. To operate it with ease, make sure to download the comprehensive Instruction Manual available for free on our website. Unlock the full potential of your Nikon NPL-302 by accessing the user manual at manualshive.com.

Share
Download
background image

4

   Applications

108  

 Pulse Laser Station NPL-302 Series Instruction Manual

Extending a line by horizontal angle offset

40.1

1.

To enter the line extension (by HA) function, 
press 

[4]

 or

Line by HA

 in the Offset 

menu.

2.

Sight the first prism (or target) and press 

[MSR1]

 

or 

[MSR2]

.

The display moves to the next screen.

3.

Sight the second prism (or target) and press 

[MSR1]

 or 

[MSR2]

.

4.

Sight the alternative place on the same vertical 
line as the required target point.

5.

To calculate the coordinates and the raw data of the target point, press 

[ENT]

.

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

Omega Engineering DFG35 Series User Manual preview
DFG35 Series
Brand: Omega Engineering Pages: 22
Bamo Pooltest 3 Instruction Manual preview
Pooltest 3
Brand: Bamo Pages: 8
Tavool MD50 User Manual preview
MD50
Brand: Tavool Pages: 12
Ecolab LMIT09/S209 Short Operating Instructions preview
LMIT09/S209
Brand: Ecolab Pages: 95
GMC-I Prosys CP 2005 Operating Instructions Manual preview
CP 2005
Brand: GMC-I Prosys Pages: 10
S&S Northern Merlin PM2 Product Data Sheet preview
Merlin PM2
Brand: S&S Northern Pages: 5
Johnson & Associates GSM-500 Operation & Maintenance Manual preview
GSM-500
Brand: Johnson & Associates Pages: 33
PCE Health and Fitness PCE-TG1XX Manual preview
PCE-TG1XX
Brand: PCE Health and Fitness Pages: 11
Parker SensoControl Serviceman SCM-150 Series Operating Instructions Manual preview
SensoControl Serviceman SCM-150 Series
Brand: Parker Pages: 39
L.R. Baggs M1 ACTIVE Installation Manual & Users Manual preview
M1 ACTIVE
Brand: L.R. Baggs Pages: 6
Princeton Instruments HRS-300 Operating Instructions Manual preview
HRS-300
Brand: Princeton Instruments Pages: 28
S&T TPMS1209C01 User Manual preview
TPMS1209C01
Brand: S&T Pages: 23
HyQuest Solutions TB71 User Manual preview
TB71
Brand: HyQuest Solutions Pages: 25
Endress+Hauser Proline Promag 50H Manual preview
Proline Promag 50H
Brand: Endress+Hauser Pages: 52
Kawai AnytimeX Owner'S Manual preview
AnytimeX
Brand: Kawai Pages: 28
THORLABS LTS150 User Manual preview
LTS150
Brand: THORLABS Pages: 63
PTC Instruments e2000 512D Manual preview
e2000 512D
Brand: PTC Instruments Pages: 2
Kensington KS-PH-221-DELUXE User Manual preview
KS-PH-221-DELUXE
Brand: Kensington Pages: 14

Brands by name

Popular brands

Load more brands