manualshive.com logo in svg

Nikon NPL-302 Series, Instruction Manual

The Nikon NPL-302 Series, a cutting-edge surveying instrument, combines accuracy and reliability. To operate it with ease, make sure to download the comprehensive Instruction Manual available for free on our website. Unlock the full potential of your Nikon NPL-302 by accessing the user manual at manualshive.com.

Share
Download
background image

Safety

Pulse Laser Station NPL-302 Series Instruction Manual  

 ix

C

Warning – 

Use only the specified battery charger (part number Q-75U/E) to 

charge the battery pack (part number BC-65). Using other chargers, such as 
a charger with part number Q-7U/E or Q-7C, may cause the battery pack to 
catch fire or rupture. (The BC-65 cannot be charged by the Q-7U/E or Q-7C.)

C

Warning – 

Do not cover the battery charger while the battery pack is being 

recharged. The charger must be able to dissipate heat adequately. Coverings 
such as blankets or clothing can cause the charger to overheat.

C

Warning – 

Avoid recharging the battery pack in humid or dusty places, in 

direct sunlight, or near heat sources. Do not recharge the battery pack when it 
is wet. If you do, you may receive electric shocks or burns, or the battery pack 
may overheat or catch fire.

C

Warning – 

Although the battery pack (part number BC-65) has an auto-reset 

circuit breaker, you should take care not to short circuit the contacts. Short 
circuits can cause the battery pack to catch fire or burn you.

C

Warning – 

Never burn or heat the battery. Doing so may cause the battery to 

leak or rupture. A leaking or ruptured battery can cause serious injury.

C

Warning – 

Before storing the battery pack or battery charger, cover the 

contact points with insulation tape. If you do not cover the contact points, the 
battery pack or charger may short circuit, causing fire, burns, or damage to 
the instrument.

C

Warning – 

The battery BC-65 is not waterproof on its own. Do not get the 

battery wet when it is removed from the instrument. If water seeps into the 
battery, it may cause a fire or burns.

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

UEi MM100 Instruction Manual preview
MM100
Brand: UEi Pages: 4
TA Q Series Getting Started Manual preview
Q Series
Brand: TA Pages: 58
E+E Elektronik OMNIPORT 30 Operating Manual preview
OMNIPORT 30
Brand: E+E Elektronik Pages: 40
Keithley 236 Applications Manual preview
236
Brand: Keithley Pages: 201
JGR RL1 Manual preview
RL1
Brand: JGR Pages: 12
Mahr MarSurf PS 10 Original Operating Instructions preview
MarSurf PS 10
Brand: Mahr Pages: 384
S.E. International USB Inspector Operation Manual preview
USB Inspector
Brand: S.E. International Pages: 30
SZBJ BM5263 Operator'S Manual preview
BM5263
Brand: SZBJ Pages: 2
Omega DP-7600 User Manual preview
DP-7600
Brand: Omega Pages: 31
Neogen Corporation AccuPoint 2 ATP Manual preview
AccuPoint 2 ATP
Brand: Neogen Corporation Pages: 16
Aktobis WDH-318KC Manual preview
WDH-318KC
Brand: Aktobis Pages: 7
PCB Piezotronics IMI SENSORS 604B11 Installation And Operating Manual preview
IMI SENSORS 604B11
Brand: PCB Piezotronics Pages: 19
Lutron Electronics YK-2001PHA Operation Manual preview
YK-2001PHA
Brand: Lutron Electronics Pages: 43
Eno Scientific Well Watch 700 User Manual preview
Well Watch 700
Brand: Eno Scientific Pages: 47
Obvius A90DC-10 Installation And Operation Manual preview
A90DC-10
Brand: Obvius Pages: 15
Ecodhome 01335-1800-00 Installation Manual preview
01335-1800-00
Brand: Ecodhome Pages: 12
A&D LCC07 Series Instruction Manual preview
LCC07 Series
Brand: A&D Pages: 2
Hammond XH-200 Basic Features Manual preview
XH-200
Brand: Hammond Pages: 106

Brands by name

Popular brands

Load more brands