Nikon NPL-302 Series Instruction Manual Download

Page: 169 / 234

Menu Key

Pulse Laser Station NPL-302 Series Instruction Manual

149

When you press

[ENT]

on the last line of the edit

screen, a confirmation screen appears.

Do one of the following:

–

To accept the changes and return to the
data view screen, press

[ENT]

or the

Yes

softkey.

–

To return to the edit screen, press

[ESC]

the

softkey.

Editing coordinate records

You can edit PT, CD, and coordinate values in coordinate records.

Do one of the following:

–

In the XYZ screen, use

[^]

[v]

to highlight

the record that you want to edit. Then press
the

Edit

softkey.

–

In the detailed data screen, press the

Edit

softkey.

When you change the HT of an SS, SO, or CP measurement record, its Z
coordinate is recalculated.

You cannot edit the coordinate record for the current station.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands