Nikon NPL-302 Series Instruction Manual Download

Page: 93 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

Measure to PT2 and press

[ENT]

When the instrument has enough data, it
calculates the station (STN) coordinates.

–

If more than the minimum required data is
available, a standard deviation screen
appears.

–

To take measurements to strengthen
geometry of the resection, press the

Add

softkey. For information about the

View

softkey, see Advanced feature: Viewing
and deleting a measurement in resection, page 74.

When the results are satisfactory, record the
station. To do this, press

[ENT]

or the

REC

softkey.

Enter the height of instrument, if required.
Press

[ENT]

. The ST field defaults to the last

recorded PT + 1.

10.

To change the station name, move to the ST
field and edit or replace the text.

BS defaults to the first observed point.

11.

To change the BS, press the

Change

softkey.

If you have set Split ST to Yes, the ST field defaults to the last recorded ST
value + 1. For more information, see Others settings, page 140.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands