manualshive.com logo in svg

Motorola HT 1000, User Manual

The Motorola HT1000 is a versatile two-way radio designed for seamless communication in demanding environments. Unlock its full potential with the comprehensive User Manual, available for free download from our website. Easily access detailed instructions and optimize your experience with this reliable and rugged communication tool.

Share
Download
background image

124

Singletone TX Pretime

Enter a value directly or use the UP/DOWN arrow keys to make your 
selection. This is the time period preceding the transmission of the 
Single Tone during which silent carrier or carrier with PL (if on a PL 
channel) is transmitted. This time can range from 0 (zero) to 6375 ms 
in 25-ms increments.

The default is 250.

Singletone Sidetone

This sidetone applies to Single Tone encode via PTT only. Use the UP/
DOWN arrow keys to enable/disable the sidetone feedback during 
Single Tone encode. The sidetone is a 900 Hz tone which lasts for the 
duration of the transmitted Single Tone. 

The default is Enabled.

Side button accept tone

Use the UP/DOWN arrow keys to enable/disable the Accept Tone that 
is generated as feedback to the user when a Single Tone is encoded via 
a side button. The accept tone is a 900 Hz, 75 ms tone.

The default is Disabled.

Note: 

In order for Single Tones to operate properly, they must be

enabled for each channel on the CHANNEL CONFIGURATION
screen (

F4/F4/F2

). If Single Tone on a side button is desired, the side

button must be assigned on the SIDE BUTTON CONFIGURATION
screen (

F4/F3/F3

).

Summary of Contents for HT 1000














































































































































































































Reviews:

No comments

Related manuals for HT 1000

Durapac SPES3502AR Instruction Manual preview
SPES3502AR
Brand: Durapac Pages: 12
3B SCIENTIFIC PHYSICS FG100 Instruction Sheet preview
FG100
Brand: 3B SCIENTIFIC PHYSICS Pages: 5
G-project G-Grip User Manual preview
G-Grip
Brand: G-project Pages: 14
Xoro HMT 390 Operation Manual preview
HMT 390
Brand: Xoro Pages: 32
Cristec UEYPOPL/12-4Q/3D Manual preview
UEYPOPL/12-4Q/3D
Brand: Cristec Pages: 54
NextBase SDV17-SQ Operating Instructions Manual preview
SDV17-SQ
Brand: NextBase Pages: 52
Sangean PR-D4VW Instruction Manual preview
PR-D4VW
Brand: Sangean Pages: 24
Hama DIR150BT Operating Instructions Manual preview
DIR150BT
Brand: Hama Pages: 50
Weelko F-333A Instruction Manual preview
F-333A
Brand: Weelko Pages: 13
N-Gear THE FLASH 610 User Manual preview
THE FLASH 610
Brand: N-Gear Pages: 15
Uniden UBC125XLT Owner'S Manual preview
UBC125XLT
Brand: Uniden Pages: 72
Icom V10MR Quick User Programming Manual preview
V10MR
Brand: Icom Pages: 6
DAISHIN Hard Gear SGE3500BSi Owner'S Manual preview
Hard Gear SGE3500BSi
Brand: DAISHIN Pages: 28
Xylem WEDECO SMOevo PLUS Series Original Manual preview
WEDECO SMOevo PLUS Series
Brand: Xylem Pages: 179
Generac Power Systems TOWER LIGHT CUBE+ HYBRID Owner'S Manual preview
TOWER LIGHT CUBE+ HYBRID
Brand: Generac Power Systems Pages: 74
Champion 46598 Owner'S Manual & Operating Instructions preview
46598
Brand: Champion Pages: 29
Hayter CONDOR 510D Operator'S Manual preview
CONDOR 510D
Brand: Hayter Pages: 52
Vertex Standard VX-4500 Series Service Manual preview
VX-4500 Series
Brand: Vertex Standard Pages: 45

Brands by name

Popular brands

Load more brands