manualshive.com logo in svg

Motorola HT 1000, User Manual

The Motorola HT1000 is a versatile two-way radio designed for seamless communication in demanding environments. Unlock its full potential with the comprehensive User Manual, available for free download from our website. Easily access detailed instructions and optimize your experience with this reliable and rugged communication tool.

Share
Download
background image

145

Receive Squelch

Use the UP/DOWN arrow keys to set Receive Squelch to one of the 
following: DPL, TPL, TPL/Quik-Call II, DPL/Quik-Call II, Carrier 
Squelch, or Quik-Call II. Carrier Squelch unmutes when carrier is 
detected. DPL and TPL unmute when a carrier with proper coding is 
detected. Quik-Call II unmutes the radio when the proper tone 
sequence is detected. Combinations of TPL/DPL and Quik-Call II can 
also be used.

Note: 

A low-level hum or buzz in the received audio MAY be

experienced when the TPL code OZ (254.1 Hz) is used. This PL
code is at the high end of the sub-audible frequency range and
may be heard in the audio under certain circumstances. Use of
this code should be avoided if possible.

The default is Carrier Squelch.

Quik-Call Type

This field will not be visible unless the Receive Squelch field is set to Quik-
Call II or PL/QC II. Use the UP/DOWN arrow keys to select the Quik-
Call II type. The line under Receive Squelch shows the Quik-Call II 
type. The Quik-Call II type will be set to one of the following:

The default is Individual Call.

Note: 

The Quik-Call II frequencies and codes table is provided

in the Appendix of this manual and are assigned on the QUIK-
CALL II OPTIONS screen (

F4/F3/F7/F2

).

PL Code (Receive)

Use the UP/DOWN arrow keys to select the Private Line codes/
frequencies. This field is used to select the Receive PL mode and 
frequency or DPL mode and code. This line will be blank unless the 
Receive Squelch field is set to PL, DPL, or a combination of Quik-Call II with 
PL or DPL.

The Receive PL code can be either a DPL code or a TPL code taken from 
the DPL/TPL tables. The TPL frequency may be entered directly from 
the keyboard so that TPLs not in the standard table are supported. 
When a frequency is entered directly, it will be encoded and then 
immediately decoded and re-displayed.

For both Transmit and Receive TPL, the frequency you entered may change 
by several tenths of a Hz when you exit this screen and return to it. However, 
due to differences in the algorithms for encoding and decoding TPL, 
the Receive TPL frequencies will change less often on re-display than 
the Transmit TPL frequencies. 

Individual 
Call

Sets the radio to decode only the A-B individual call tone 
combination.

Long Tone B

Sets the radio to decode the A-B individual call tone 
combination OR the long tone B group call.

Dual Call

Sets the radio to decode the A-B individual call tone 
combination OR the C-D group call tone combination.

Summary of Contents for HT 1000














































































































































































































Reviews:

No comments

Related manuals for HT 1000

Yaesu FT-270R Technical Supplement preview
FT-270R
Brand: Yaesu Pages: 34
Sven PS-36 Operation Manual preview
PS-36
Brand: Sven Pages: 16
Virgin boomtube Quick Start Manual preview
boomtube
Brand: Virgin Pages: 2
Mercedes-Benz HiLine Operation Manual preview
HiLine
Brand: Mercedes-Benz Pages: 23
RDL STICK-ON ST-RG1 Quick Start Manual preview
STICK-ON ST-RG1
Brand: RDL Pages: 2
GE 3-7025 User Manual preview
3-7025
Brand: GE Pages: 14
GE Superadio 7-2887 Use And Care Manual preview
Superadio 7-2887
Brand: GE Pages: 9
GE Superadio 7-2867 Use And Care Manual preview
Superadio 7-2867
Brand: GE Pages: 16
Curtis RCD668 Owner'S Manual preview
RCD668
Brand: Curtis Pages: 6
Curtis RCD340 User Manual preview
RCD340
Brand: Curtis Pages: 6
Johnson Controls tyco NG-1 1000 Manual preview
tyco NG-1 1000
Brand: Johnson Controls Pages: 6
Hitachi PDV512 Instruction Manual preview
PDV512
Brand: Hitachi Pages: 25
Hitachi E40 Safety Instructions And Instruction Manual preview
E40
Brand: Hitachi Pages: 24
Hitachi PDV313 Instruction Manual preview
PDV313
Brand: Hitachi Pages: 25
Hitachi E24SB Safety Instructions And Instruction Manual preview
E24SB
Brand: Hitachi Pages: 40
Hitachi E24SC Safety Instructions And Instruction Manual preview
E24SC
Brand: Hitachi Pages: 36
Hitachi PDV342E Instruction Manual preview
PDV342E
Brand: Hitachi Pages: 36
Hitachi WH-900 Service Manual preview
WH-900
Brand: Hitachi Pages: 5

Brands by name

Popular brands

Load more brands