Motorola HT 1000 User Manual Download | Manualshive

Page: 85 / 205

background image

79

Channel Wrap-around Alert

Use the UP/DOWN arrows to select Enabled or Disabled. Depending
on the setting in the Channel Wrap-around field, the Wrap-around
Alert or No Wrap-around Alert option will be enabled.

The default is Enabled.

Note:

Channel Selector Alert and Channel Wrap-around Alert are

mutually exclusive. You must disable one before enabling the
other.

Channel Selector Alert

Use the UP/DOWN arrows to select Enabled or Disabled. When this
field is enabled, an alert tone is generated when either of the Channel
Selector buttons are pressed.

The default is Disabled.

Note:

The Channel Selector Alert and Channel Wrap-around Alert

features are mutually exclusive. You MUST disable one before
enabling the other.

Enabled

An alert is generated whenever the wrap-around occurs.

Disabled

An alert is generated whenever the user attempts to go
beyond the beginning or the end of the Channel list.

«
...
83
84
85
86
87
...
»

Summary of Contents for HT 1000














































































































































































































Reviews:

No comments

Related manuals for HT 1000

Brand: Yaesu Pages: 34

Brand: Oxygen Pages: 15

Brand: AudioSonic Pages: 45

Brand: Eton Pages: 43

Brand: MAKINEX Pages: 23

Brand: Takstar Pages: 40

Brand: Sangean Pages: 43

Brand: Briggs & Stratton Pages: 56

Brand: Powermate Pages: 16

Brand: Clas Ohlson Pages: 4

EXPLORER 1000 PLUS

Brand: Jackery Pages: 48

A915000JA-LI555

Brand: Parker Balston Pages: 14

Brand: Kongsberg Pages: 52

Brand: Kaito Pages: 6

Brand: Curtis Pages: 1

Brand: UNIMO Technology Pages: 32

SkyWay Excel PTP Series

Brand: Solectek Pages: 24

Brand: Hyundai Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands